How do I reset my Eaton Fuller transmission?
Note: You may use a PC-based service tool, such as ServiceRanger, to clear fault codes.
- Place shift lever in neutral.
- Set parking brake.
- Turn key on with engine off.
- Turn key off and on 6 times within 5 seconds ending with key on.
- Turn the key off and allow the system to power.
How much does it cost to rebuild a transmission in a semi?
Although different things affect semi truck transmission repair cost, in general, the transmissions typically cost at least $1,500 just for the part alone. What’s more, they can run over $4,000, depending on the issues listed above.
How much is an Eaton Fuller transmission?
Overall, you can expect to spend about $5,000 on an Eaton Fuller transmission rebuild. The typical price range is between $3,000 on the low end and $7,000 on the high end.
Is Eaton and Fuller the same company?
In 1958 Eaton Corporation acquired Fuller Manufacturing. The company name changed once again in 1965 to Eaton Yale & Towne Inc.
What does F mean on transmission?
Active fault code
Flashing “F” in Gear Display Indicates that the transmission has detected an Active fault code. This fault code can be accessed with the ServiceRanger diagnostic software.
How heavy is a 18 speed transmission?
Eaton 18 speed Transmission
| SPECIFICATIONS | CAPACITY | WEIGHT* |
|---|---|---|
| RTLO-16918B | 1650 lbs.ft. [2237 Nm] | 716 lbs. [324.77 kg] |
| RTLO-18918B | 1850 lbs.ft. [2508 Nm] | 716 lbs. [324.77 kg] |
| RTLO-20918B | 2050 lbs.ft. [2779 Nm] | 716 lbs. [324.77 kg] |
| RTLO-22918B | 2250 lbs.ft. [3050 Nm] | 716 lbs. [324.77 kg] |
What is code 88 on Eaton autoshift?
Note: The gear display may flash a “88” at key on, which is a normal power-up test of the display.
What is Eaton UltraShift?
Eaton Corp. has introduced the Eaton Fuller UltraShift 10-speed, a fully automated heavy-duty truck transmission that provides North American fleets with fully automatic, two-pedal operation.
What does CA mean in semi truck?
CA (Cab-to-Axle) The distance from the back of the truck cab to the center of the rear axle. Clear or effective CA is the distance from the rear surface of any obstruction behind the cab to the center of the rear axle.
How long does it take a shop to rebuild transmission?
3 to 5 days
The Better Solution. A reman saves you and your transmission specialist time – bottom line. In a rebuild situation, the transmission must be removed, disassembled, parts purchased, reassembled, and installed back in your vehicle. All of this can take 3 to 5 days.
Where can I buy an Eaton Fuller transmission?
At Pro Gear and Transmission Inc. We are your one-stop Eaton fuller transmission shop. Call your experts today. We offer a wide range of service and products for all makes and models including new Eaton transmissions, used Eaton transmissions, rebuilt or remanufactured transmissions, Eaton transmission parts and rebuild kits.
Where can I service my Eaton transmission and clutches?
You depend on the experts at your local Cummins Sales and Service branch* to service your engines. Now depend on us to maintain your Eaton transmissions and clutches. Cummins Sales and Service locations have expanded their service offerings to include Eaton transmissions and clutches, providing you with a one-stop shop for maintenance and repairs*.
Do You rebuild Eaton Transmissions?
We rebuild all Eaton transmissions. We service and install any and all Eaton Truck and Equipment Differentials for Freightliner, Kenworth, International, Peterbilt, Volvo, Mack, Ford, GMC, Crane Carrier, CCC, Autocar, Western Star, Dodge and Oshkosh trucks. If playback doesn’t begin shortly, try restarting your device.
Are Eaton service technicians Certified to work on heavy-duty engines?
Regardless of heavy-duty engine make, our factory-certified technicians are trained to provide all types of service to the following Eaton automated and manual transmissions and clutches using Genuine Eaton parts: *during the entire warranty period including but not limited to OEM warranty periods.